Part 21 Report - 1998-701
ACCESSION #: 9811180227
Coltec Industries
Fairbanks Morse
Engine Division
701 White Avenue
Beloit, WI 53511-5492
www.fairbanksmorse.com
608/364-4411
Fax: 608/364-0382
November 11, 1998
Document Control Desk File No. 98-001
U.S. Nuclear Regulatory Commission
Washington, DC 20555
Subject: FM-Alco 251 Engine, Wrist Pin Assembly, Catalog No.: 2420021-2
On November 11, 1998, Coltec Industries, Fairbanks Engine Division (FMED), became aware of a potential safety hazard associated with the wrist pin assemblies for FM-Alco 251 engines. The wrist pin assembly consists of a wrist pin and a sleeve fitted in the bore of the wrist pin and held in place by rolling each end which causes a tight friction fit. The sleeves of the subject wrist pin assemblies were supplied with an incorrect material, which is not suitable for rolling - expansion. Therefore, the friction fit between the pin and the sleeve may not be sufficient, which could cause the sleeve to become lose and possibly contact the finer. A drawing of the wrist pin assembly is attached.
Corrective actions have been taken to prevent recurrence, which include no longer using the supplier of the defective wrist pins, and renaming the Receipt Inspectors and the Quality Assurance Supervisor to perform proper inspections and reviews of certifications.
The only affected utility is Consumers Power - Palisades, which received a total of 36 wrist pin assemblies between 1995 and 1996. It should be noted that no failures have occurred to date and the problems with the wrist pin assemblies occurred in commercial applications after many thousands of hours of cyclic operation. FM-Alco 251 engines in nuclear applications are not typically subjected to this type of operation. However, it is recommended that the subject wrist pins be replaced with pin assemblies made with the correct sleeve material.
|
Sincerely,
James C. Golding
Senior Quality Assurance Engineer
|
Cc: |
Terry Gill
Mary Armfield
Ted Stevenson |
A Division of Coltec Industries Inc
11/14/1998 |
U.S. Nuclear Regulatory Commission Operations Center Event Report |
Page 1 |
General Information or Other (GEN) |
Event# 35030 |
Rep Org: |
COLTEC INDUSTRIES |
Notification Date/Time: |
11/13/1998 |
|
|
|
|
15:45 (EST) |
Licensee: |
COLTEC INDUSTRIES |
Event Date/Time: |
11/13/1998 |
|
|
|
|
14:45 (CST) |
|
|
|
Last Modification: |
11/13/1998 |
Region: |
3 |
|
Docket #: |
|
City: |
Beloit |
|
Agreement State: |
No |
County: |
|
|
License #: |
|
State: |
WI |
|
|
|
NRC Notified by: |
James Golding |
|
Notifications: |
GEOFFREY WRIGHT R3 |
HO Ops Officer: |
JOHN MacKINNON |
|
|
VERN HODGE NRR |
Emergency Class: |
NON EMERGENCY |
10 CFR Section: |
21.21 UNSPECIFIED PARAGRAPH |
Coltec Industries, Fairbanks Engine Division (FMED) became aware of a potential safety hazard associated with the wrist pin assemblies of FM-Alco 251 engines. Only affects Palisades Nuclear Power Plant.
10 CFR PART 21 REPORT
On November 11, 1998, Coltec Industries, Fairbanks Engine Division (FMED), became aware of a potential safety hazard associated with the wrist pin assemblies for FM-Alco 251 engines. The wrist pin assembly consists of a wrist pin and a sleeve fitted in the bore of the wrist pin and held in place by rolling each end which causes a tight friction fit. The sleeves of the subject wrist pin assemblies were supplied with an incorrect material, which is not suitable for rolling - expansion. Therefore, the friction fit between the pin and the sleeve may not be sufficient, which could cause the sleeve to become loose and possibly contact the liner.
Corrective actions have been taken to prevent recurrence, which includes no longer using the supplier of the defective wrist pin, and retraining the Receipt Inspectors and the Quality Assurance Supervisor to perform proper inspections and reviews of certifications.
Consumers Power - Palisades is the only utility, which received a total of 36 wrist pin assemblies between 1995 and 1996. It should be noted that no failures have occurred to date and the problems with the wrist pin assemblies occurred in commercial applications after many thousands of hours of cyclic operation. FM-Alco 251 engines in nuclear applications are not typically subjected to this type of operation. However, it is recommended that the subject pins be replaced with pin assemblies made with the correct sleeve material.
BF5316
Coltec Industries
FAX TO: |
Fairbanks Moras Engine Division |
PAGE |
|
|
|
DATE |
ATTN: |
NRC Operations Center |
OUR REF |
FROM: |
James Golding, Coltec Industries |
YOUR REF |
|
|
SUBJECT: |
Part 21 File No. 98-001 |
|
Attached is notification of part 21 File No. 98-001. Written notification will follow. If there are any questions please contact me at (608) 364-8315. |
|
James Golding |
|
TELECOPY NUMBERS
PARTS MARKETING |
Chart "THIRD ANGLE PROJECT"
*** END OF DOCUMENT ***
Page Last Reviewed/Updated Tuesday, March 09, 2021